← All serum protocols

If you study extracellular vesicles from cultured cells, the vesicles in the serum get in the way. This protocol shows how to deplete EVs and exosomes from FBS by ultracentrifugation, which alternatives exist and how to check the result.

Why serum EVs are a problem

FBS contains large amounts of bovine extracellular vesicles (EVs), including exosomes. If you collect EVs from conditioned medium, the bovine vesicles end up in your preparation and are hard to tell apart from those of your cells. They also carry RNA and proteins that can change the behaviour of the cells you study.

Options at a glance

MethodAdvantagesLimits
Ultracentrifugation, 18 hStandard method, keeps most serum proteinsNeeds an ultracentrifuge; removes most but not all EVs
UltrafiltrationFast, very low residual EVsAlso removes large proteins above the cut-off
Serum-free medium in the collection phaseNo bovine EVs at allCells must tolerate serum-free conditions

Materials

  • FBS, thawed slowly at 2–8 °C
  • Basal medium for dilution, e.g. DMEM or RPMI 1640
  • Ultracentrifuge with a fixed-angle or swinging-bucket rotor and suitable bottles or tubes
  • Sterile pipettes for careful removal of the supernatant
  • 0.2 µm sterile filter with low protein binding (PES)

Step-by-step protocol (ultracentrifugation)

1. Prepare the serum

  1. Dilute the serum with basal medium, for example to 20–50 % serum. Undiluted serum is viscous, and EVs sediment more slowly.
  2. Fill the tubes, balance them carefully and close them.

2. Spin

  1. Centrifuge at 100,000–120,000 × g for 18 hours at 4 °C. Long spins remove clearly more EVs than the short runs of one to two hours that were common earlier.
  2. If you change rotors, adjust the time to the rotor’s k-factor so the result stays comparable.

3. Collect the supernatant

  1. Remove the supernatant carefully from the top without disturbing the pellet.
  2. Leave the lowest part of the liquid, roughly the bottom tenth, in the tube and discard it with the pellet.

4. Filter and store

  1. Sterile-filter the supernatant through 0.2 µm.
  2. Dilute to the final serum concentration with medium, aliquot, label as “EV-depleted” with date and lot, and store at −20 °C.

Quality control

  • Particles: compare particle counts before and after depletion, for example by nanoparticle tracking analysis.
  • EV markers: check typical markers such as CD9, CD63 and CD81 by Western blot, using antibodies that recognise the bovine proteins.
  • Medium control: run unconditioned medium with the depleted serum through your EV isolation as well. This shows what is left from the serum.
  • Growth: check growth and morphology of your cells, because some cell types grow more slowly in EV-depleted serum.

Practical tips

  • Prepare one large batch for the whole study. Depletion efficiency varies between runs.
  • Heat inactivation does not remove EVs. If you need it, do it before the spin, because heating creates aggregates that the spin then removes.
  • Many labs grow cells in normal FBS and switch to EV-depleted or serum-free medium only for the collection phase of 24–72 hours.

Frequently asked questions

Is ultracentrifuged FBS completely free of EVs?

No. Even an 18-hour spin leaves some bovine EVs and RNA in the serum. For sensitive RNA work, include a medium control or use serum-free conditions during collection.

Why dilute the serum before ultracentrifugation?

Diluted serum is less viscous, so vesicles sediment faster and depletion is more complete in the same time.

Is there an alternative to EV-depleted serum?

Yes. A serum-free medium avoids bovine EVs completely. Mesenchymal stem cells, a common source of EVs, can be grown in serum-free media developed for this purpose.

Related

Test sample of your lot

Test the exact lot before you order. If it works for you, we reserve it for up to 36 months – no prepayment.

Name